FIXADUR

Polyurethane adhesive with EXTRAORDINARY adhesion for laying ceramic tiles and glass mosaic on the most difficult surfaces.

  • FIXADUR is a state-of-the-art waterproof adhesive, formulated to satisfy even the most demanding requirements in any installation.
  • Completely waterproof (100%)
  • Excellent adhesion to most substrates: ceramics, concrete, iron, paint (in good condition), PVC, mortar, wood, metals and polyureas.
  • Maximum mechanical strength in a very short time
  • Extraordinary flexibility.
  • Highly resistant to ageing.

Eco Design
Eco Fixcer

All Fixcer products are environmentally friendly. Fixcer manufactures with sustainable construction parameters and complies with the EN14.001 standard to reduce environmental impact.

Eco Fixcer
View Vídeo
Technical Data Sheet
Safety Data Sheet
Declaration of Performance
Chemical Resistance

All Fixcer products are environmentally friendly. Fixcer manufactures with sustainable construction parameters and complies with the EN14.001 standard to reduce environmental impact.

Eco Fixcer
Eco Fixcer

COLORS

FIELDS OF APPLICATION

  • FIXADUR is the adhesive to use on the most difficult surfaces:
  • Non-absorbent substrates such as linoleum, PVC, polyester, EPDM rubber, steel, old ceramics and cold and hot polyurea
  • It is also ideal for sticking material to difficult surfaces such as gypsum, fibre cement, cured wood, chipboard and glass.
  • It is the ideal adhesive for bonding marble, granite, slate, stoneware, porcelain stoneware, vitreous mosaic and green marble tiles, among others.
  • FIXADUR is a state-of-the-art waterproof adhesive, formulated to satisfy even the most demanding requirements in any installation.

HOW IS IT APPLIED?

Before using FIXADUR we recommend as follows:

  • The substrate must have a minimum strength of 1 N/mm2, since the adhesion of FIXADUR will greatly exceed this threshold. Check that the temperature is at least +3ºC above the dew point. (Ask the Technical Dept. for more information). In general, the temperature of the substrate should be within the following range: +10ºC- +30ºC.

Mortar or concrete substrates:

  • The mortar substrates where FIXADUR is to be applied must be perfectly set. The presence of moisture will affect adhesive adhesion.

Bonded PVC substrates:

  • In these cases, apply PRIMER PARA ELASTICER to the bonded PVC. Apply the product, then rub it in and leave to dry for 2 minutes.

Metal substrates:

  • In these cases, remove any grease or oil residue with FIXAQUA DISOLVENTE. Apply the product, then rub it in and leave to dry for 2 minutes.

Gypsum substrates:

  • In these cases, prime the substrate with ‘HIDROPRIMER’ and leave it to dry for at least 3 hours (at +20ºC) before you start bonding the tiles.

Preparing the components:

  • The temperature range MUST be between +10ºC and +30ºC. Do not use this product in temperatures outside of this range.

Preparing the mix:

  • The components are perfectly pre-dosed. The proportions should not be altered. A set consists of: 1 large and 1 small bottle of liquid and 1 bag of powder. Pre-mix the resin component with the bag of powder. When the mix is homogeneous, add the hardening agent and stir with a spiral mixer at a low RPM (maximum 400 RPM) for 2-3 minutes.
  • To extend the shelf life of the stirred mix, divide the contents into smaller containers.
  • Apply FIXADUR with a toothed trowel according to the size of the piece to be fitted and the planimetry of the substrate. Comb the adhesive parallel to the short side of the piece to facilitate air release. Put the piece in the right position and use a back and forth motion to fix it in place. FIXADUR is fast: just spread adhesive on the area to be laid immediately afterwards.
  • With FIXADUR, you can also make a waterproof layer beforehand using the flat metal trowel. In this case allow the layer to dry for 24 hours before application
  • For difficult applications, outdoor locations or bonding of parts larger than 40×40, use the double-bonding technique. Where floorings are subject to vibrations, we recommend leaving wide joints of at least 5 mm.
  • Protect the newly installed flooring from excessive heat, frost, rain, etc., for at least 24 hours after installation.
  • Download the FIXADUR Data Sheet for full technical details as well as step-by-step application instructions that will ensure correct, safe application.

HOW IS IT RECYCLED?

  • Use cardboard and paper recycling bins to dispose of unusable and empty sacks.
  • Use plastic recycling bins for unusable and empty plastic packaging. 
  • Mortar residues and leftover building materials must be disposed of at the appropriate green point or recycling location for your district.

RELATED PRODUCTS

Item added to cart View Cart Checkout